产品资料

脉冲发生器接收器

如果您对该产品感兴趣的话,可以
产品名称: 脉冲发生器接收器
产品型号: 5072PR/5073PR/5077PR
产品展商: 泛美-奥林巴斯
产品文档:
 脉冲发生接受器

简单介绍

5072PR手动控制超声脉冲发生器接收器既可用于常规应用,又可用于高频应用。用于一般检测的理想配置是35 MHz(-3 dB)带宽和尖脉冲发生器。 优化的宽带激励会产生优良的时域恢复效果,特别是在15~30 MHz的情况下。 5073PR手动控制超声脉冲发生器接收器既可用于常规应用,又可用于高频应用。 在对轴向和近表面分辨率要求极高的应用中


脉冲发生器接收器  的详细介绍
      5072PR手动控制超声脉冲发生器接收器既可用于常规应用,又可用于高频应用。用于一般检测的理想配置是35 MHz(-3 dB)带宽和尖脉冲发生器。 优化的宽带激励会产生优良的时域恢复效果,特别是在15~30 MHz的情况下。
        5073PR手动控制超声脉冲发生器接收器既可用于常规应用,又可用于高频应用。 在对轴向和近表面分辨率要求极高的应用中,这款设备的75 MHz(-3 dB)带宽和快速上升的尖脉冲发生器可提高50 MHz探头的工作性能。
       5077PR手动控制超声脉冲发生器接收器具有35 MHz(-3 dB)带宽和方波脉冲发生器接收器,是一款可使散射材料的响应*大化的理想设备。方波脉冲发生器在与10 MHz或10 MHz以下的探头一起使用进行检测时,会发挥出其明显的优势。
       5058PR高压超声脉冲发生器接收器专用于对声束衰减性强的材料的检测和测量应用。其脉冲发生器*高可发射900伏激励脉冲,从而可适当对低频探头进行补偿。

Specifications*

PULSER 5072PR 5073PR 5077PR
Pulse Type 
(main bang):
Negative Negative Impulse Negative Square Wave
Rise Time 
(10% to 90%):
Typically 5 ns, 10 ns max Typically <2 ns

Typically <10 ns, 20 ns max 
(rise and fall time)

Available Pulse Voltage: 
(no load) 

-360 V -180 V Select -400 V, -300 V, -200 V, -100 V
Available Pulse Energy: 13, 26, 52, or 104 µjoules 2, 4, 8, or 16 µjoules N/A
Damping: Select 15, 17, 20, 25, 36, 50,
100, or 500 ohms
12, 14, 17, 20, 25, 33, 50, or 
100 ohms
N/A
Pulse Width: N/A N/A 10 preset fixed widths: 15-20,10, 7.5, 5.0-6.0, 3.5-4.0, 2-2.25, 1.0, 0.5, 0.25, 0.1 MHz. 
Variable +/-25% fine vernier tuning for each width.
Mode:   Pulse Echo or Thru-Transmission  
Isolation (53 dB min): Typically 62 dB at 10 MHz Typically 62 dB at 50 MHz Typically 62 dB at 10 MHz
Pulse Repetition Rate: 
(Internal)
100, 200, 500, 1000, 2000, or 5000 Hz 200, 500, 1000, 2000, 5000, 10000, or 20000 Hz

100, 200, 500, 1000, 2000, 5000 Hz, except that maximum PRF is limited to: 2000 Hz FOR 0.5 MHz tranducers, 1000 MHz for 0.25 MHz transducers, and 50 Hz for 0.1 MHz transducers.

Pulse Repetition Rate: 0-6 kHz 
(External)
0-10 kHz 0-5 kHz (observe limitations of PRF versus pulse width)
Synch Output Pulse: 3 V into 50 ohms    
External Trigger Input: 
(in series with 10 Kohms)
2.4 V into 1000 PF 
200 ns minimum pulse width
2.4 V into 1000 PF 
200 ns minimum pulse width
2.4 V into 1000 PF 
50 ns minimum pulse width
 
RECEIVER 5072PR 5073PR 5077PR
Maximum Bandwidth: 
(-3 dB, RL=50 ohms)
1 kHz - 35 MHz 1 kHz - 75 MHz 1 kHz - 35 MHz
Voltage Gain: 0-59, 1 dB steps (RL=50 ohms) 0-39, 1 dB steps (RL=50 ohms) 0-59, 1 dB steps (RL=50 ohms)
Phase:   inverting or non-inverting (internal switch)  
Attenuator Range: 0-59, 1 dB steps (RL=50 ohms) 0-49, 1 dB steps (RL=50 ohms)

0-49, 1 dB steps (RL=50 ohms)

High Pass Filter: 1 kHz (out) or 1 MHz 1 kHz (out) or 5 MHz 1 kHz (out) or 1 MHz
Low Pass Filter: 35 MHz (out) or 10 MHz 75 MHz (out) or 20 MHz 35 MHz (out) or 10 MHz
Noise: 70 µV pk-pk typical, referred to input, BW=35 MHz 200 µV pk-pk typical, referred to input, BW=75 MHz 70 µV pk-pk typical, referred to input, BW=35 MHz
Max Signal Output:   +/-1V pk., terminated in 50 ohms  
Input Resistance: 
(Thru-Transmission)
500 ohms linear range 
100 ohms > linear range
100 ohms linear range 
50 ohms at levels > linear range
500 ohms
Output Impedance: 50 ohms 50 ohms 50 ohms
Maximum Input Power: 400 mW 400 mW 500 mW
 
UNIT 5072PR,5073PR,5077PR
Input/Output: External Trigger In, Sync Out, RF Out, T/R and R: All BNC female connectors
Power Main Requirements:

100/120/220/240 VAC, 50/60 Hz

Operating Temperature: 0-50°C
Size and Weight: 7" W x 3.5" H x 9.1" D (178 mm x 89 mm x 232 mm); 5 lbs (2.3 kg)

ORDERING INFORMATION: Each model is shipped with a power cord and operator manual. Transducers and cables are sold separately. 
Our sales department is available to discuss your application in detail and to assist with transducer selection.

*All specifications are subject to change without notice.

产品留言
标题
联系人
联系电话
内容
验证码
点击换一张
注:1.可以使用快捷键Alt+S或Ctrl+Enter发送信息!
2.如有必要,请您留下您的详细联系方式!

京公网安备 11010802025952号